• There is a also a useful supported parts list for ScanImage software

Coherent Chameleon Vision (A, below). Specs are here

Sutter MOM (Moveable Objective Microscope).

• Fluorescence path
  • Point Grey Grasshopper CCD camera (A)
  • Olympus tube lens (B)
  • Olympus epi-fluorescence path (from BX51) (C)
  • Mirrors of MOM core (L)
  • Objective lens (variable) (E)
• Two-photon detection path
  • Objective lens (E)
  • Dichroic mirror in MOM core (L)
  • Hamamatsu PMTs (and collection optics) (F)
  • Hamamatsu pre-amps (G)
• Other
  • PMT Power supply (H)
  • iMac (O)
  • Power meters (J)
  • Power sensor (K)
  • Stage (D)
  • Cage light (M)
  • Cage (N)
  • Thorlabs cubes (for controlling half-wave plate, fluorescence LED, and shutter (I)
  • Odour presentation manifold (P)
  • Aaron's junk (Q)

Fast scan 6mm mirrors (Cambridge 6215) and scanner driver electronics (includes two Cambridge Technologies 671XX-HP Micromax scanner driver boards)

Hamamatsu H7422 P40-MOD unprotected GAsP PMTs (Hamamatsu part number, H10770PB-40 SEL) and Hamamatsu C3719 pre amps. The power supply is labeled “Sutter PS-2” but it looks suspiciously like two Hamamatsu model C3830 supplies piled into a Sutter box. I can't find any info on the PS-2, but the Hamatsu specs are here or here. This is just a guess on my part, so if you are really fussed about these specs, it would probably be best to contact Sutter.

• Filters/dichroic for detection
  • Chroma
• Table
  • Newport Smart Table UT2 with IQ Damping Technology
• Attenuation
  • Thorlabs (WPH05M) rotating half-wave plate (B) and fixed (GL10-B) Glan-Laser polariser (D) to control beam intensity
  • Non-polarising (Thorlabs CM1-BS014) 50:50 beam splitter (F) to divide the beam
  • Variable (Thorlabs BE02-05-B) beam expander (I) to control objective (over/under) filling
• Power measurement
  • J beam sampler (reflected portion is angle dependent - currently around 3%)
  • L Power meter
    • note that you need to re-calibrate the linear relationship between power meter reading and power at the objective back aperture if you
    • knock/realign J
    • put telescope in
• Shutters
  • Thorlabs SH05 (G) This shutter is normally opened by scanImage during a run. Additionally, it is connected to an interlock on the shroud door, forced closed when the door is open.
• Beam steering on table
  • Thorlabs mirrors (E, H)
• Beam trap
  • Thorlabs BT610/M (C, K)
• PCs for control
  • Lenovo Thinkstation with NI DAQ board (NI 6110E) for ScanImage operation
  • iMac with Micromanager

• Zeiss 20x 1.0 NA M27 (70 mm parfocal, 75 also avail w more DIC)
• Olympus 20x 1.0 NA 25 diam
• Olympus 40x 0.8 NA (RMS mount)
• Olympus 25x 1.05 NA (? mount)
• Nikon 25x water 1.1 NA with correction collar

• Svoboda ScanImage and Ephus

Alex set up the filter cube for the PMTs as below:

         RED CHANNEL
       *-------------*
       | HQ605/75 \/ |
   *---*-------------*   
G  |   |\*
R  | E | \*
E  | T |  \*
E  | 5 |   \*
N  | 2 |    \*
   | 5 |     \*
C  | / |      \*
H  | 7 |       \*
A  | 0 |        \*
N  |   |         \*
N  |   |          \*
E  | > |           \*
L  |   |            \*
   *---*

The filters are by Chroma and the arrows point towards the coated side.